Magnetic Jewelry Clasp

Seashell Jewelry Making

This article will describe some tips and advices how to drill holes of seashells in making of seashells jewelry. Drilling holes of seashells is quite difficult and shall be done very carefully. Seashells are often quite fragile. Be very careful drilling holes in them and also try to pick shells that are not chipping or flaking at the edges. There are a few precautions that we should know and take in order to prevent the seashells from crack and damage.

1 - Drilling bits

Use A Dremel. A Dremel tool works well also because it's higher speed than your regular drill. Especially good for delicate shells; use a very small bit. It wasn't possible to use a very fast speed because the hardness of the shell made the drill bit slip and mark the surface. Once the hole was started, continue with slow because even then the drill would overheat from the effort. We had to stop every 5 minutes and allow the drill to cool down for about 20 minutes to half an hour. Also suggested to use diamond points to drill.

2 - Water

When you drill with diamond points, always use water to cool the points or they will fail quickly. This also keeps the dust down, but wear a good quality filter mask or use a vacuum to catch any dust/spray. Seashell dust is toxic, and I don't mean a little bit toxic. You can really hurt yourself if you breath it in, or get it into your eyes, a cut or sore, or ingest it. Sometimes the particulates are so small you don't realize they're in the air around you. When you breathe this dust in, it gets embedded in your lungs and it won't come out. It will literally be there forever, and it's toxic. Obviously, don't put your drill in the water, just the tip of the bit doing the drilling.

3 - Start Drilling

Make sure the drill bit is sharp, and that you are using a high speed drill. Use the smallest drill bit that will accommodate the chain or whatever you're putting through the shell. Secure the shell firmly in a vise or other arrangement to make sure it cannot move during the drilling.If the shell is thin, I would suggest putting tape over the spot where you are drilling to help prevent the shell from splintering or cracking.Lay the shell with the top up so that if spintering does occur as the bit reaches the other side, any splintering will be on the bottom (back) of the shell.

If you're not comfortable using a drill, practice first on some scrap shells before drilling in those you want to use.

Now when you start to drill, you're going to do it like this: hold the drill in a straight up and down position so that the hole will be straight. Hold the drill firmly so that the bit won't go skidding across the surface of the stone. (Now you know why you need practice pieces.) You're going to touch the drill bit down semi-firmly, like you mean it, but then lift the drill bit out of the hole so water can pool inside it. Repeat. You can do it pretty quickly, too. Touch down, lift, touch down, lift, etc. When you're almost all the way though, Stop. Flip your stone over and begin to drill from the other side. This will prevent a "blow out" or chipping the stone or glass where the hole should be. It takes practice to do this, so don't be hard on yourself. Glass and stone will pretty much drill the same. Anything else may be unpredictable, so a practice piece is necessary.

Seashell Jewelry Making

Seashells Jewelry

Before to start painting of seashells that we collected at the beach, first thing we should do is cleaning the seashells. There are several known methods for cleaning your live seashell specimens.

Burying: This is easiest way to clean the Seashells but will take about two months. Dig a hole somewhere in around your home or yard and bury the seashells about 18 inches (deep enough so animals will not dig them up). It shall need to remain buried until insects, larvae, worms, and bacteria remove all the tissue. The longer you leave them the better.

Freezing: Use a Ziplock bag and cover it with full of water, zip it and then place in the freezer. When you are ready to clean them, let the bag thaw at room temperature until completely defrosted.

Boiling: Boil the seashells in the pot with some of water for a few minutes (more seashells need longer). Use tongs to remove one shell at a time. So you don't burn yourself, grasp shell with gloves or a towel and gently pull out the animal tissue inside.

Heating: As long as you don't mind the smell in your microwave, this is an easy method. The time it takes to cook your seashells can really vary by microwave, so just try it until you figure out how long for each seashell. Grasp cooked seashell with gloves or a towel and gently pull out the animal tissue inside.

After that, the last step that we should do is bleaching the seashells. When no tissue remains, soak the seashells in a 50-50 solution of bleach and water. The length of time depends on the type of seashells and the quantity of seashells being cleaned. We must remove them after the "periostracum" is gone. The periostracum is the flaky, leathery covering that covers most live seashells. To make your seashells a nice finish and more shining, you can wipe them with mineral or baby oil.

Seashell Jewelry Making

This article will describe some tips and advices how to drill holes of seashells in making of seashells jewelry. Drilling holes of seashells is quite difficult and shall be done very carefully. Seashells are often quite fragile. Be very careful drilling holes in them and also try to pick shells that are not chipping or flaking at the edges. There are a few precautions that we should know and take in order to prevent the seashells from crack and damage.

1 - Drilling bits

Use A Dremel. A Dremel tool works well also because it's higher speed than your regular drill. Especially good for delicate shells; use a very small bit. It wasn't possible to use a very fast speed because the hardness of the shell made the drill bit slip and mark the surface. Once the hole was started, continue with slow because even then the drill would overheat from the effort. We had to stop every 5 minutes and allow the drill to cool down for about 20 minutes to half an hour. Also suggested to use diamond points to drill.

2 - Water

When you drill with diamond points, always use water to cool the points or they will fail quickly. This also keeps the dust down, but wear a good quality filter mask or use a vacuum to catch any dust/spray. Seashell dust is toxic, and I don't mean a little bit toxic. You can really hurt yourself if you breath it in, or get it into your eyes, a cut or sore, or ingest it. Sometimes the particulates are so small you don't realize they're in the air around you. When you breathe this dust in, it gets embedded in your lungs and it won't come out. It will literally be there forever, and it's toxic. Obviously, don't put your drill in the water, just the tip of the bit doing the drilling.

3 - Start Drilling

Make sure the drill bit is sharp, and that you are using a high speed drill. Use the smallest drill bit that will accommodate the chain or whatever you're putting through the shell. Secure the shell firmly in a vise or other arrangement to make sure it cannot move during the drilling.If the shell is thin, I would suggest putting tape over the spot where you are drilling to help prevent the shell from splintering or cracking.Lay the shell with the top up so that if spintering does occur as the bit reaches the other side, any splintering will be on the bottom (back) of the shell.

If you're not comfortable using a drill, practice first on some scrap shells before drilling in those you want to use.

Now when you start to drill, you're going to do it like this: hold the drill in a straight up and down position so that the hole will be straight. Hold the drill firmly so that the bit won't go skidding across the surface of the stone. (Now you know why you need practice pieces.) You're going to touch the drill bit down semi-firmly, like you mean it, but then lift the drill bit out of the hole so water can pool inside it. Repeat. You can do it pretty quickly, too. Touch down, lift, touch down, lift, etc. When you're almost all the way though, Stop. Flip your stone over and begin to drill from the other side. This will prevent a "blow out" or chipping the stone or glass where the hole should be. It takes practice to do this, so don't be hard on yourself. Glass and stone will pretty much drill the same. Anything else may be unpredictable, so a practice piece is necessary.

Seashell Jewelry Making